What is a Low Noise Amplifier?

A low noise amplifier (LNA) is an electronic device that amplifies weak signals at its input without adding significant noise. These amplifiers are typically used in receivers. For LNAs the most important specifications are:

  • Gain
  • Noise Figure
  • Linearity

Gain

The LNA’s gain refers to its ability to increase the value of the input signal. It is most often specified in dB. Typical gain values for an LNA are between 10 and 30 dB.

Noise Figure

Noise figure provides a measure of the noise contribution due to the LNA itself. In the picture below, the LNA amplifies both the signal and noise present at its input equally. In addition, the output includes noise due to the LNA. This in turn reduces the signal-to-noise ratio. A good LNA contributes very little noise to the overall picture.

picture1

Linearity

The linearity of an LNA is a measure of its ability to amplify the signal without distortion. When an LNA is operating linearly, the output power in dB is the sum of the input signal and the gain.  However, as the input signal level increases beyond a certain point, the output starts to level off and the LNA is no longer linear.

In the picture below, the LNA is operating linearly when the signal present at its input has an amplitude of -60 dBm. However, as the input signal is increased to 0 dBm, the device is no longer linear, the output signal is distorted, the gain is no longer 20 dB and the output signal amplitude is only +5 dBm.

picture2

Visit our stores:

Ebay Store

Tindie Store

 

 

Advertisements

13 thoughts on “What is a Low Noise Amplifier?

  1. Hi there,

    Can you please tell me what’s the best LNA optimized just for Airband listening you can deliver?

    Thank you

      1. Thank you.
        Can you please provide me a table (showing the typical Attenuation) with more values ranging from 85MHz to 140MHz?

      2. Yes, the gain at 85 MHz is -12 dB; 90 MHz is -9 dB; 100 MHz is +3dB; 110 MHz is +17 dB; 120 MHz is +20 dB; 130 MHz is +20 dB and 140 MHz is +18 dB. If you want higher attenuation in the FM band, you can Cascade with a FM notch filter (after this filter LNA)

      3. Many thanks for the data provided. Guess I’ll buy your LNA when I have the funds. So the best configuration would be: Antenna -> FM notch filter -> LNA. Correct?

  2. Thoughts on using your LNA’s to directly drive an antenna, as an indoor re-radiating antenna for GPS, The GPS receiver will only be about 50cm way from the antenna.

      1. Thoughts on cascading the LNA’s. Two of the pre-filtered-gnss-lna-gps-l1-l5-glonass-beidou LNA’s directly in series. I need about 80-90dB gain total, Based off of -130dBi, so about -40dBi at the re-radiating antenna. Or should I simply get one of 40dB LNA’s instead of a second filtered GPS LNA. In which case which one. There are two available. If using the two different LNA, which order should I put them in.

      2. L1
        Doing gps module testing on an m2m module for contract production. sim868.

        Thinking 25dB more gain should be ok, as want to keep it too below -140dB outside the building. As that is the US standards, I am not in the US, but good to follow standard I guess.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s